1 data sheet ! note: 1. this datasheet is downloaded from the website of murata manufacturing co., ltd. therefore, it?s speci? cations are subject to change or our products in it may be discontinued without advance notice. please check with our sales representatives or product engineers before ordering. 2. this datasheet has only typical speci? cations because there is no space for detailed speci? cations. therefore, please approve our product speci? cations or transact the approval sheet for product speci? cations before ordering. http://www.murata.com/ 1 noise suppression products/emi suppression filters > ac line filters > common mode choke coil 2012.7.5 o this data sheet is applied for ac line filters common mode choke coil used for general electronics equipment for your design. ac line filters common mode choke coil pla10 series c dimension (in mm) 17.5 max. 18 max. 130.5 100.5 16 max. ?0.9 max. 3.51 (1) [(2)] (4) [(3)] (4) [(1)] (3) [(2)] c insertion loss characteristics (main) 0.1 1 10 100 0 20 40 60 80 0.01 frequency (mhz) pla10an1522r0r2 pla10an1821r7r2 pla10an2221r5r2 pla10an3021r3r2 pla10an3521r2r2 pla10an5521r0r2 insertion loss (db) pla10an7420r8r2 pla10an1030r7r2 pla10an1230r6r2 pla10an2030r5r2 pla10an3030r4r2 pla10an4330r3r2 c rated value ( p : packaging code) part number common mode inductance (min.) rated current rated voltage insulation resistance (min.) pla10an1522r0r2 p 1.5mh 2.0a 300v 100m ohm pla10an1821r7r2 p 1.8mh 1.7a 300v 100m ohm pla10an2221r5r2 p 2.2mh 1.5a 300v 100m ohm pla10an3021r3r2 p 3.0mh 1.3a 300v 100m ohm pla10an3521r2r2 p 3.5mh 1.2a 300v 100m ohm pla10an5521r0r2 p 5.5mh 1.0a 300v 100m ohm pla10an7420r8r2 p 7.4mh 0.8a 300v 100m ohm pla10an1030r7r2 p 10.0mh 0.7a 300v 100m ohm pla10an1230r6r2 p 12.0mh 0.6a 300v 100m ohm pla10an2030r5r2 p 20.0mh 0.5a 300v 100m ohm pla10an3030r4r2 p 30.0mh 0.4a 300v 100m ohm pla10an4330r3r2 p 43.0mh 0.3a 300v 100m ohm operating temperature range: -25c to 60c winding temperature rise (at rated current): 60c (max.) continued on the following page. pla10 series standard winding type
2 data sheet ! note: 1. this datasheet is downloaded from the website of murata manufacturing co., ltd. therefore, it?s speci? cations are subject to change or our products in it may be discontinued without advance notice. please check with our sales representatives or product engineers before ordering. 2. this datasheet has only typical speci? cations because there is no space for detailed speci? cations. therefore, please approve our product speci? cations or transact the approval sheet for product speci? cations before ordering. http://www.murata.com/ 2 noise suppression products/emi suppression filters > ac line filters > common mode choke coil 2012.7.5 o this data sheet is applied for ac line filters common mode choke coil used for general electronics equipment for your design. c equivalent circuit (1) (4) (2) (3) n1 n2 n1 : n2 = 1 : 1 no polarity. c packaging code packaging minimum quantity m magazine 1800 b box 1260 pla10 series sectional winding type continued from the preceding page. c dimension (in mm) 17.5 max. 16 max. 18 max. 130.5 100.5 ?0.9 max. 3.51 (1) (4) [(2)] (4) [(1)] (3) [(2)] [(3)] c insertion loss characteristics (main) 0.1 1 10 100 0 20 40 60 80 0.01 frequency (mhz) insertion loss (db) pla10an9012r0d2 pla10an1321r7d2 pla10an1821r5d2 pla10an2021r3d2 pla10an3621r0d2 pla10an7720r7d2 pla10an1330r5d2 pla10an2230r4d2 pla10an3630r3d2 c rated value ( p : packaging code) part number common mode inductance (min.) rated current rated voltage insulation resistance (min.) pla10an9012r0d2 p 0.9mh 2.0a 300v 100m ohm pla10an1321r7d2 p 1.3mh 1.7a 300v 100m ohm pla10an1821r5d2 p 1.8mh 1.5a 300v 100m ohm pla10an2021r3d2 p 2.0mh 1.3a 300v 100m ohm pla10an3621r0d2 p 3.6mh 1.0a 300v 100m ohm pla10an7720r7d2 p 7.7mh 0.7a 300v 100m ohm pla10an1330r5d2 p 13.0mh 0.5a 300v 100m ohm pla10an2230r4d2 p 22.0mh 0.4a 300v 100m ohm pla10an3630r3d2 p 36.0mh 0.3a 300v 100m ohm operating temperature range: -25c to 60c winding temperature rise (at rated current): 60c (max.) continued on the following page.
3 data sheet ! note: 1. this datasheet is downloaded from the website of murata manufacturing co., ltd. therefore, it?s speci? cations are subject to change or our products in it may be discontinued without advance notice. please check with our sales representatives or product engineers before ordering. 2. this datasheet has only typical speci? cations because there is no space for detailed speci? cations. therefore, please approve our product speci? cations or transact the approval sheet for product speci? cations before ordering. http://www.murata.com/ 3 noise suppression products/emi suppression filters > ac line filters > common mode choke coil 2012.7.5 o this data sheet is applied for ac line filters common mode choke coil used for general electronics equipment for your design. continued from the preceding page. c ! caution (rating) 1. rated current operating current should not exceed the rated value. even if operating current is under the rated value, adequate ventilation is required to avoid excessive heat generated within the product (choke coil) and from surrounding heat sources. if exceeding these conditions, excessive heat may cause fumes or permanent damage to the product. please ensure that product (choke coil) is evaluated and con? rmed against the speci? cation when it is mounted in your ? nal assembled product. -> winding temperature should be less than 120 degree c. *as for fkob series winding temperature should be less than 95 degree c. maximum allowable temperature at the surface of coil (ambient temperature + winding temperature rise) is in accordance with each safety standard applicable to ? nal assembled product. when the temperature at winding exceeds maximum allowable temperature of safety standard, the rated current should be derated. 2. inrush current inrush current should not exceed 10 times rated current within 1/4 cycle of 50/60hz commercial power line. inrush current should be limited to a minimum of 10 seconds after last inrush. if these conditions are exceeded, excessive heat may cause fumes or permanent damage to the component, or at worst cause ignition. c notice (soldering and mounting) magnetic flux leakage choke coils generate small amounts of magnetic ? ux leakage that may adversely affect equipment operation according to component arrangement. testing should be completed on ? nal assembly to ensure equipment performance is not affected. c notice (other) coil humming noise magnetic ? ux generated between coil and core or between the choke coil windings creates repulsive power between the coil windings. this repulsive power causes the coil winding to vibrate and create a humming noise. the amount of hum produced by the coil is proportionate to the amount of harmonic distortion generated by the operating current. this does not in? uence the electrical performance of the coils, but it should be considered and tested in actual circuit application.
|
